A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

在二元柔壁自适应风洞中利用面元法进行三元模型实验

简要叙述了在西北工业大学二元柔壁自适应风洞中利用面元法进行二元半机翼模型试验的研究情况，分析了面元法的基本思想和部分试验结果。     

连续逻辑DYL电路在测试系统中的应用

本文利用DYL多元逻辑电路的特点,提出求极值和中间值的“地址”的方法和电路。使DYL多元逻辑电路的应用更加完善。     

随振动量级增加卫星结构频率下移的分析

对卫星振动频率随量级增加而出现下降，即振动频率“漂移”的现象进行了初步分析。发现随振动量级的增加。结构的非线性表现突出。结构的刚度下降和阻尼增加，可认为主要是由蜂窝材料的非线性因素所致。     

翼板颤振主动抑制的无限维非线性分析

 <正> 1.混合动力学系统的Hopf分叉定理 本文将Marsden-McCracken关于分布参数的Hopf分叉定理推广至混合动力学系统。 设在积空间X=E×R~n中依赖参数μ的演化方程为     

双轴应力下含裂纹加筋曲板剩余强度的弹塑性有限元计算

 采用考虑了大应变的弹塑性有限元方法,以裂纹尖端张开角为断裂准则,实现了双向受载条件下加筋曲板中裂纹起裂到失稳整个扩展过程的数值模拟计算;还对与加筋曲板有同样尺寸的加筋平板进行了分析和计算。结果表明,所提出的分析方法和所采用的断裂准则适用于对含裂纹加筋结构所进行的剩余强度分析。     

运载火箭阻尼安装板的设计

 <正>运载火箭在起飞和着陆时的瞬态载荷和飞行过程中的气动力的随机激励都是宽频带的。在这种环境中安装精密仪器的仪表板若采用过去常规的橡皮减振器减振已很难保证在较宽频带内都能起到应有的减振作用。利用阻尼材料做成的夹层板减振，国内外已做了大量的工作^[t~3]，取得了较为明显的效果。本文针对产品设计中要解决的减振问题，提出了设计思想、计算分析与试验方法。     

简谐激励下弯曲薄板的非线性运动方程

推导了两端固定和两端简支的弯曲薄板在其支承简谐激励下的运动微分方程,并利用Galerkin方法对其进行了离散化处理。     

螺桨滑流对全机绕流干扰的数值计算

 数值计算采用面元法。在桨叶及全机面元的控制点上强加 Neumann条件以实现滑流与全机流场的相互耦合。计算中考虑了三维螺桨滑流的收缩及其对流场的影响。最后对运七全机气动力作了计算。结果表明 ,滑流对全机放襟翼状态升力特性有明显影响 ,使全机力矩特性产生较大变化。计算结果与实验值吻合良好。该方法对单发或多发螺桨飞机均适用     

基于参数化模型和遗传算法的复合材料加筋壁板结构选型优化研究

针对复合材料加筋壁板的结构优化选型问题,采用辅助层压板和添加极小弹性模量材料的复合材料加筋壁板有限元建模方法,应用PATRAN/NASTRAN的参数化建模功能和遗传算法相结合的复合材料加筋壁板的优化方法,对5种复合材料结构形式进行了从2000N/mm到6000N/mm压缩载荷下的结构优化分析。结果表明,当载荷小于4500N/mm时,最有效的加筋壁板结构型式为J型;当压缩载荷大于4500N/mm时,最有效的加筋壁板结构型式为I型。